• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Doors Repair - How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors are a great option to connect your home to the outdoors. They offer a pleasant and easy transition. By keeping the air in your home, they can help you save money on cooling or heating bills.

But with time, your sliding glass or French doors could lose their luster. Fortunately, simple repairs can keep them looking and operating as new.

Weatherstripping

It's 5 AM and you're taking your dog out for his morning constitutional when you stumble into the puddle of water in front of the sliding patio doors. You look around and discover that the rain of last night blew in through the patio door seals. This isn't going to be a simple task. With a little patience, and a few tools, you can fix it and prevent your dog's feet from getting wet and cold.

The key is to replace the weatherstripping which closes the gap between the door and the jamb, preventing drafts, pests and moisture. It also helps keep your energy bills low. If you inspect your doors and windows you will be able to tell if the weatherstripping needs to be replaced or not.

There are a variety of weatherstripping that are available, including felt, open-cell foam and thermoplastic rubber, and metals like bronze or copper. Each has its pros and disadvantages. Open-cell foam and felt are both inexpensive, but they also tend to be noticeable and ineffective at blocking airflow. Vinyl is more expensive, but it's durable and is resistant to moisture. Rubber is a good option for areas with high traffic because it does not wear out as quickly.

To install new weatherstripping, first remove the patio door from the frame by loosening the roller adjustment screws using a screwdriver. Then using a flathead screwdriver, remove the plugs that hold the weatherstripping in place at the bottom of the frame. Then, remove the weatherstripping that was previously in place and scrape any adhesive from the bottom of the frame. Then, cut the replacement to the proper length, peel back the plastic strip at one side and then apply it to the jamb with a putty knife.

When you're done, reinstall the door and re-adjust the roller screws until the door is positioned in the track and is closed properly. Then, apply caulk to the place where the stationary panel bypasses the sliding patio door repairs near me door and where the edge of the stationary panel reaches the frame. This is a less-reliable seal than the weatherstripping however, it will last for a while.

Handles and Locks

Patio door handles and locks play an important role in the security of your home. As time passes, they may get worn or damaged and require replacement. In addition, the spindle that connects the interior and exterior handles may also need to be replaced.

To replace a handle on a patio sliding door repair near me door, remove the old one first, dislodging any screws that held it in the place. Once the old handle is removed then use a level to make sure the door is straight prior to installing the new handle. If the door isn't straight it could cause problems with the lock and cause issues in the future.

Close and open the handle a few times after installing it to ensure it is working properly. If you experience any issues, you should consult the manufacturer's instructions or a hardware specialist for assistance. To avoid future issues, it is a good idea to also lubricate your lock mechanism with silicone-based lubricant.

The most popular type of patio door lock is a mortise latch. It is typically constructed of steel and is placed inside a pocket which has been cut into the door frame. These locks are commonly used on sliding wood and aluminum doors. Before you purchase a new mortise lock, you need to take some measurements. You will need to know the location of mounting holes and the location in the keyway lock.

Certain patio door frame repair door handles have an locking mechanism that is built into the handle. These handles feature the key cylinder in a rectangular shape that fits into the handle's keyway. If you have this type of patio door both the outside and inside locks are combined into one. This type of patio door is often found on aluminum sliding doors.

If your patio door repair service near me door latch isn't staying fixed It could be due to the lock tongue isn't grasping the hasp of the jamb correctly. Another possibility is that your sliding door isn't aligned to the side jamb. Open the door one inch and then position it against the frame. This will reveal if there is a gap between the door jamb and the door. If there is a gap, reposition the rollers to the bottom left or the right of the patio so that it is perfectly parallel to the jamb.

Misalignment

As time passes the tracks and rollers of the door may lose their alignment. This could cause the doors to become stuck or difficult to move. It can also allow cold air and drafts to be able to enter your home, which could reduce the efficiency of your home's energy usage. Luckily, misalignment is easy to correct and stop. Applying a silicone-based lubricant to the tracks and rollers will help your doors move smoothly once more. It's a good idea apply this every so often to keep your doors in peak operating condition.

A torn screen can also be an issue. It could cause inconvenience or even risky. It could also stop the doors from opening and closing properly, causing energy loss. In some cases, the screen can be repaired but in others, the door needs to be replaced. If you've damaged your window screen, make sure you wash it thoroughly. Also, don't turn the handles of the door the wrong way.

Over time, hinges will loosen due to normal wear and tear or heavy usage. Regularly tightening the screws will help correct this issue and ensure that your doors shut tightly. This is an easy task which you can perform by yourself, however if you're not comfortable doing it, you should consult an expert to ensure that your doors are correctly aligned and secure.

You should also clean the tracks and rollers of your patio doors regularly. Simple vacuuming or brushing will take away dust and other debris that could hinder the smooth operation your patio doors. You can utilize a special tool for tough dirt or rust. It is possible to correct any misalignment by tightening, or examining the screws. However, sometimes it is necessary to replace the hinges in order to ensure a durable seal.

If your patio doors' frames are warped or sagging they could affect their alignment and performance. Warping or shifting can happen due to changes in the foundation of your home, but it could also be caused by poor installation or simply due to frequent use. A professional can repair or replace your patio sliding door repair door frame, and make sure it is properly aligned. This will allow it to perform its best.

Rollers

Patio doors that slide are great to let the outside in and letting plenty of light, however they do require a bit of maintenance to ensure they slide smoothly. If you notice that you have to really pull the handle to get your door to move, or isn't as easy to slide as it did in the past it could be due to the rollers. Over time the lower track could get clogged by dirt, dust, and mud. This makes it difficult for rollers to move. You can try cleaning it and spraying it with a lubricant like 2Slick.

If the tracks are cleaned but the rollers not moving freely it's time to replace the tracks. There are many replacement rollers to suit your door and kind of track you have. These can be purchased at the majority of hardware stores, but you'll require a companion to help with the removal and installation of the rollers. Before you purchase replacements, take a good picture of the roller assembly that is placed in the door frame, so experts can determine the exact model and the type you need. They can also look out for identifying features such as bumps or dimples cutouts, flared edges, or cutouts to narrow down the replacement options.

After replacing the rollers, you'll have to reinstall the sliding door back into its frame. This is a very heavy door, and you might require help. Examine if there are screws securing the track on either side of frame. If there are you must ensure that they are loose enough for the door's bottom to fall into the channel above the frame. Remove the screen door from the opening. Make sure it's clear of the track rollers, track and track.

When the new rollers are installed, carefully insert the door into the frame and then swing it into place. If the rollers are adjustable you can adjust them to ensure that the door has enough clearance.