• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Doors Repair - How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors are a great way to connect your home with the outside. They provide a comfortable and easy transition. They can also help you save money on heating and cooling bills by keeping air inside your home.

But with time your sliding glass or French doors could lose their shine. Fortunately, simple fixes can keep them looking and functioning as new.

Weatherstripping

You're walking your dog to the park around 5 AM when you step in a puddle right next to your sliding patio door. You glance around and realize that last night's rain blew in through the seals of your patio doors. This isn't going to be a simple task. With a bit of patience and a few basic tools you can fix the problem and save your dog's feet from getting wet and cold.

It is important to replace the weatherstripping, which closes the gap between your door and jamb. This will prevent drafts, pests, and moisture. This will also keep your energy bills down. A quick examination of your windows and doors will show you whether the weatherstripping in good condition or requires replacement.

There are a variety of weatherstripping to choose from that include open-cell and felt foam, vinyl and thermoplastic rubber, as well as metals like bronze or copper. Each type has advantages tilt and slide patio door repairs near me disadvantages. Open cell foam and felt are both inexpensive, but they tend to be ineffective and noticeable at blocking airflow. Vinyl is more expensive, however, it is durable and resists moisture. Rubber is a great choice for areas with heavy traffic since it will not wear out as quickly.

For installing new weatherstripping, you must first remove the patio doors from the frame using a screwdriver to loosen the screws that adjust the rollers. Then using a flathead screwdriver unscrew the plugs that keep the weatherstripping in place at the bottom of the frame. Remove the weatherstripping you have previously removed from the frame and clean any adhesive remnants. Then, cut the new to the proper length, peel off the plastic strip at the other end, and then apply it with a putty knife to the jamb.

After you're done, put back the door and readjust the roller screws so that the door sits in the track and shuts properly. Apply waterproof caulk where the stationary panel is positioned to block sliding doors and where the edge of the panel is the frame. This is a less reliable seal than weatherstripping, but it should be able to last for a period of time.

Handles and locks

Locks and handles for patio doors are crucial to the security of your home. Over time they can get worn or damaged and require replacement. In addition, the spindle that connects the exterior and interior handles may also need to be replaced.

To replace a handle on a patio door first, remove the old one by unscrewing any screws that are holding it in place. Once the old handle has been removed, use a level to ensure that the door is straight before installing the new handle. If the door isn't straight it could cause problems with the lock and cause issues in the future.

Once you have the new handle installed Close and then open it a few times to ensure it works effectively. If you have any problems, consult the manufacturer or a specialist in hardware for assistance. To avoid future issues, it is a good idea to also lubricate the lock mechanism using lubricant made of silicone.

The most commonly used door lock for patio doors is a mortise latch. It is usually constructed of steel and is placed inside a pocket that has been cut into the frame of the door. They are usually used on sliding doors made of aluminum and wood. When replacing a mortise lock it is important to take a few measurements prior to ordering a new one. The measurements you need to take include the mounting hole locations and the location of the keyway inside the lock.

Some handles for patio doors are equipped with an locking mechanism that is built into the handle. These handles have a rectangular key cylinder which fits into the handle's keyway. This type of patio door includes the exterior and inside locks in one piece. This type of patio doors are typically found on sliding aluminum doors.

If the latch on your patio door does not stay locked it could be because the lock tongue may not be properly catching the hasp. Another possibility is that your sliding door isn't aligned to the jamb's side. Try opening the door for about an inch and placing it against the frame to determine whether there is a gap between the door and the jamb. If there is, you can adjust the rollers on the bottom left or right of the patio door repair service near me door to get it perfectly parallel with the jamb.

Misalignment

Over time the tracks and rollers may lose their proper alignment. This can cause the doors to become stuck or difficult to move. This could also allow drafts and cold air into your home, reducing energy efficiency. Fortunately, misalignment is simple to fix and stop. Applying a silicone-based grease to the tracks and rollers can help your doors move again. It is a good idea to apply this every so often to ensure your doors are in good working order.

Another common issue with patio doors is a torn screen, which is a nuisance or even a security risk. In addition, it may hinder the doors from opening and closing properly, which can lead to energy loss. In some cases, the screen can be repaired, but in others, the door has to be replaced. If you've got a damaged window screen, be sure you wash it thoroughly. Also, make sure you don't turn the handles of the door in the wrong way.

Over time, hinges will loosen due to wear and tear or excessive usage. This can be corrected by regularly tightening screws. It's a simple job you can tackle on your own. If you're not sure doing it yourself, you must seek out a professional.

It is also recommended to clean the rollers and tracks of your patio doors regularly. A simple brushing or vacuuming will remove dirt and dust that could impede the smooth operation of your patio doors. You can also use an instrument specifically designed to clear away stubborn dirt or rust. Checking and tightening the screws on the hinges can help with misalignment however, sometimes it's necessary to replace them completely to ensure a strong and durable seal.

The alignment and performance of your patio doors can be affected when the frames are warped or sliding. Warping or shifting can be caused by foundation changes but it can also occur from poor installation or frequent use. A professional can replace or repair patio doors your patio door frame and make sure it is properly aligned. This will allow it to function at its best.

Rollers

patio door lock repairs near me doors that slide are great to let the outside in and letting plenty of light, however they do require a bit of maintenance to keep them sliding smoothly. If you have to yank the handle to get the door to move, or it isn't sliding as it used to, it could be the rollers. Over time the lower track may become clogged with dirt, sand and mud, making it difficult for the rollers to move over. Clean it and spray it with a lubricant such as 2Slick to see if it helps.

If the tracks have been cleaned but the rollers are still not sliding freely, it's time to replace them. There are a variety of replacement rollers that will fit your door and the type of track you have. You can find them at most hardware shops however you will need someone to assist you in removing and install the rollers. Take a photo of the rollers installed in the frame to help the experts identify the exact model and type you need. They can also search for identifying characteristics such as bumps, dimples and flared edges and cut-outs which can narrow down alternatives for replacement.

After replacing the rollers you will need to reinstall the sliding door back into its frame. This is a very heavy door, and you might need some help. Check to see if there are screws securing the track on either side of frame. If they are you must ensure that they are loose enough to allow the door's bottom to fall into the channel that is above the frame. Remove the screen door from the opening. Make sure it's clear of the track rollers, track and track.

After putting in the new rollers, gently place the door into the frame. Swing it down to ensure it is secured. If your rollers are adjustable, you can adjust them to ensure that the door has enough clearance.