• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. In contrast to aluminium and timber, they are not susceptible to rust or rot.

It is crucial to wash and oil UPVC windows and doors regularly. This will help avoid unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home and may even be fatal. It is essential to take the time to make sure that you're doing everything you can to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace, and they will usually fit into the frames that were previously in use very easily. However when windows with double panes are anchored by internal beading, it'll be more difficult to get rid of the panes that are in place and replace them with new ones. In this instance you'll need to find some plastic spacers that will help the new pane to fit perfectly into the frame of the window.

If you're planning to attempt to remove the window panes by yourself it is important to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric and not on the floor which could cause them to be trampled.

After the glass has been removed from the window, it's best to cover the gap with packaging tape or duct tape to block water and drafts from getting into the home until a professional comes out and fix the window. This will also act as a barrier that will prevent any intruders from gaining entry into your home. If the gap is particularly large, you might want to consider using an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber windows made of sash. However, over time, they are susceptible to a range of problems including sliding. A window that is sagging can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it is important to act swiftly to stop the issue from worsening.

Repositioning the hinges can help fix a window that is sagging. To accomplish this, you'll need to open the window repairs so that you can get to the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you have relocated your hinges. If you are happy with the fit of your window, tighten the screws to secure them in place.

If you are unable to reposition the hinges, you might need to replace the seal. Rubber seals may dry out and lose their elasticity over time, leading them to loose their elasticity. If this happens, it's important to replace the seal as soon as possible to ensure your uPVC windows are waterproof and secure from draughts.

uPVC handles could also become loose. This is often caused by screws that have been removed over time, but it can be due to the mechanism of the handle wearing out. It's relatively easy to fix a loose uPVC hand. You'll first need to close the window and perform an experiment fitting. The corners of the sash must be aligned with the casing joint. If it does not, you can use the screwdriver to loosen the handle. Then, you can turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and damp walls each time it rains, it's important to take action. Leaks of water from windows can cause structural damage to your home, and impact your ability to regulate the temperature inside your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame is either damaged or missing.

This is a simple fix that can be done by any DIYer who is competent. Depending on the severity of the issue is, old caulking might need to be removed. It is crucial to remember that when it comes to uPVC window repairs you should not be tempted to 'over-caulk and then make the area harder to clean and reduce the efficiency of your energy.

Verify that the drainage holes are free of debris in them, and also that the sill pan has been properly angled to allow the water to drain from the window. In more serious cases you may need to think about replacing the window.

Other signs of long-term water leakage include decayed sills and the appearance of black spots of mold on the walls near the window. The fungus thrives in conditions of dampness and can spread quickly throughout the house.

It is also important to note that if the leakage is coming from between the glass of your double-glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or sagging. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your upvc window repair windows are difficult to open, or slack and blow open in a breeze it could be the hinges that are at fault. They can be easily repaired by any DIYer who is skilled and are usually completed in just a few minutes.

Like any mechanical component, hinges can wear out over time. It's very simple to replace a hinge on a window however it is easier if someone helps you hold the frame.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. Look for the arrows on each hinge to determine which direction the window should be opened.

The problem can be caused due to opening the window in the wrong way or by a poor installation in the factory. Sending us a picture via our website is often enough to solve the issue. We are always happy to provide advice.

Regularly lubricating the hinges is essential. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and decrease the chance of sticking. Ideally, you should do this at least once a year. WD40 and other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by several different factors. The hinges can also be unbalanced due to wear, causing an opening between the frame and sash. They can be repaired by giving them good cleaning, but when they're beyond repair, it might be necessary to get them aligned or replaced. Second, the interlock can also become disaligned. This is located on the hinge side and may need to be cleaned. In some cases, it may be necessary to replace these.

The next most common reason for draughts is window seals. These are susceptible to being worn out or damaged over time and allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass, which will help regulate indoor temperatures, and also lessen the risk of draughts.

The final method to cut down on drafts effectively is to use a draught-excluder. These are usually fabric tubes filled with a filler which can be put on top of your window sill. These will help to block out cold air and keep your home warm and cozy!

With a little regular maintenance and repair, your upvc windows will provide an excellent level of security and insulation for your home. It is important to remember that all windows eventually wear out and it is more cost-effective to replace them instead of fixing them. So, if you are having issues with your upvc windows, it's best to seek professional assistance as soon as possible.