• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

RS-485 communication involves a driver that produces signals and a receiver that detects them. RS-485 is an example of a communication protocol. As mentioned, an example of serial communication is RS485. 2. High data rates - RS485 can support data rates up to 10 Mbps, making it suitable for applications that require high data throughput.3. It can operate reliably over distances of up to 1.2 kilometers (about 4,000 feet) or more, making it suitable for applications requiring communication across large areas. This means that it can transmit data up to 4,000 feet without needing any signal amplification or repeaters. Multimeter: You can use it to measure voltage and current on the RS485 lines, aiding in identifying wiring issues. B- lines, with high and low voltages representing binary 1 and 0 (on and off), ensuring reliable data communication. B- lines, representing a two-wire half-duplex configuration, which is the most commonly used wiring method in RS485. RS485 transmits binary signals by generating high and low voltages, representing binary 0s and 1s (on and off), enabling efficient long-distance communication in electronically noisy environments. RS422 also has stricter voltage requirements than RS485.

The signal is a voltage change across a load as low as 1.5 volts differential from a driver, with a receiver detecting a differential voltage as minute as 200 millivolts. Noise Immunity: RS-485 employs a balanced differential signaling mechanism, transmitting the signal as the voltage difference between two wires (A and B). It offers two primary wiring methods: two-wire half-duplex and four-wire full-duplex. While four-wire full-duplex exists, it is less prevalent in current applications, with the two-wire half-duplex configuration being the predominant wiring method in use today. The termination also includes pull up and pull down resistors to establish bias for each data wire for the case when the lines are not being driven by any device. It should be noted that the connection wires between each device should be kept as short as possible to minimize signal attenuation and interference, improving communication reliability. Simultaneous bidirectional communication is not possible due to the shared nature of the transmission medium. Under some conditions it can be used up to data transmission speeds of 64 Mbit/s. Through appropriate programming and configuration settings within the central control system, relevant flow measurement data can be read from the flowmeter. This makes it more immune to common-mode noise and interference, ensuring reliable communication in electrically noisy environments, such as industrial settings.

RS485 Configuration Software: Used to configure various parameters of RS 485 devices, such as baud rate, address, and error checking settings. The two-wire half-duplex system enables bidirectional data transmission between two devices, but not simultaneously. 4 Wire Full Duplex System : In this scenario, TX and RX each have their dedicated two wires for data transmission. RS232 uses a single wire to transmit data, and the voltage levels on this wire represent the binary information being transmitted. 2 Wire Half Duplex System : TX (transmit) and RX (receive) indicate the signals being sent and received, often represented by triangle orientations. It is known for being able to be used effectively over long distances and in electrically noisy environments. Long Communication Distance: RS-485 supports communication over longer distances compared to many other serial communication standards. In essence, RS485 stands as a reliable and cost-effective communication protocol, offering practitioners the means to establish efficient communication between devices over extended distances in applications ranging from industrial automation to building control systems. It may be used to control video surveillance systems or to interconnect security control panels and devices such as access control card readers.

In most cases, what is rs485 cable RS485-based devices can employ communication protocols such as Modbus and ASCII to establish communication with a central control system. Unit Load: The network’s unit load impacts the number of devices that can be attached to it. Half-Duplex and Full-Duplex Modes: RS-485 can operate in both half-duplex and full-duplex modes. Low Cost: RS-485 is a cost-effective solution for serial communication. In conclusion, RS485 is a versatile and powerful communication standard offering several advantages over other serial protocols. Devices utilizing RS485 can communicate with central control systems using communication protocols such as Modbus and ASCII. Modbus TCP, on the other hand, uses the TCP/IP protocol to transmit messages between devices. RS485 is a hardware architecture that specifies only the electrical characteristics of transmitters and receivers, without endorsing any particular transmission protocol. Oscilloscope: You can use it to view the electrical characteristics of the RS485 signals, aiding in diagnosing signal integrity issues. Control and monitoring systems: A single pair of rs485 signal cable can connect up to 32 devices, with a signal transmission distance of up to 1200m. Therefore, using rs485 cables is an ideal choice for industrial control and monitoring systems, especially those with large-scale and high dispersion.