• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a door hinge that is loose can be a doable job for most homeowners. If the screw holes have been stripped and will not hold screws, you may require wood glue and dowels to fix the door hinge.

Remove any surface corrosion. This will help the dowels remain in place and provide them a solid base to grip into.

Eliminating the Hinges

Many standard door hinges can be removed, making it simpler to move a door from one side of the frame to the other side or take the entire door off when needed. The removal of the hinges is simple for anyone with a bit of patience, although you need to know how do it right.

If the hinges are painted you'll need to get rid of the paint prior to attempting to remove the pins. If you don't, the paint will flake off and scratch your door when you attempt to lift it. Place the hinges into a stainless steel pot and fill it with water until the hinges are submerged. The hinges should remain in the pan for approximately 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

Once the pins are loosened, you can remove the hinges from the frame and door. You can make use of a screwdriver to get the job done, however it is recommended to employ a magnetic screwdriver to complete this project. This type of screwdriver is designed to remove screws made of steel and can make the work run much more quickly.

It is a good practice to spray lubricant on the hinges before attempting to remove them. A simple lubricant can make the process to go more quickly and help you remove the pins and screws. You can purchase this kind of lubricant at most hardware and home improvement stores.

The number of hinges required will also depend on the type of door you have, and how it's installed. Solid-cored and heavier doors will require more hinges while hollow-cored doors that are lighter may only need two or three.

Understanding the different types of hinges can help you determine which one is suitable for your situation. Exterior Replacement Upvc Hinges are typically designed to support the door's weight and interior hinges need to be able to support lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may lose its grip and then begin to slide or hang crookedly. This can cause problems however, it's usually simple to fix. Retightening the screw will typically solve the problem. However, if the screw holes have been stripped out, this can be more difficult. However, there is a trick to get the holes back in place that utilizes a wood dowel.

Start by drilling out the old hole using an appropriate drill bit close to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. The dowel should be cut to a length the same as the screw to ensure a tight fit. Then, reinstall the screw and tighten it to the desired degree of tightness. If the door continues to have an tendency to get stuck the door, then add a second dowel to the gap and repeat the procedure. Be sure to close the door slowly in order to check the perimeter clearances after each adjustment.

You could also use a wood plug instead of the dowel. It's also possible, but may take some time to put in. You can use the wood piece that has been whittled to the proper size. If you don't have a wooden tool, you can also use toothpicks or wooden matches.

After you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the head of the screw smaller so that it does not rub against the edge of the door when it's open and closed. This will make it much easier to tighten the screws when reinstalling hinges.

Once you've reinstalled your hinge, be sure to grease it with a dry lubricant in order to help keep it from getting stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. You should apply a thin coat and allow it to take around 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you can do a few simple repairs. Check that the screws that hold the hinge plate to the door frame and the frame are in good condition. If they're loose, tighten them using a screwdriver or power drill. Be careful not to over tighten the screws, because this can cause gaps to appear at the trim joints or more seriously, tear out the threads.

If the problem is the hinge plates are separating, you can reattach the plates by applying wood glue to the back of them and then inserting toothpicks or wooden dowels into the holes. The toothpicks or dowels will give a solid foundation for the screws and help prevent the plates from shifting when you drive them into place. Allow the glue to dry before attaching the hinge.

Another common cause of hinges that are loose is that the screws are stripped or missing. This problem can be fixed by replacing the screws. Use a drill bit that is similar to the size of the screw hole to avoid drilling into the jamb or hinge.

Close the door once you have reattached your hinge and examine the gap between the frame and the window door repairs locks glass hinges. The gap should be the thickness of a penny all around or less if an old door was not hung correctly. If the hinges were put in place correctly, this shouldn't be a problem.

If you find that the hinges are loose, you can try adding an extra thicker shim between the window hinge repair cost plate and the mounting surface to add some extra space. You can also take off the hinge pin and then pound it down with a heavy hammer to tighten it or use an entirely new hinge. You can also lubricate your replacement hinges using mineral oil or jojoba to reduce friction and hold them in place. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky and will also extend their life.

Cleaning the Hinges

The constant movement of a hinge creates friction, which attracts dust particles. Without regular cleaning and lubrication, the particles become stuck in the moving parts of a door hinge and accumulate over time. The hinge will become stiff and creaky, and its appearance can rapidly change. Regular cleaning, lubrication and inspections will maintain the functionality and quality of hinges on a door.

Inspect the hinges to see how much rust has accumulated on their surface. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you're able to save the hinges, remove any loose rust using wire brush and steel wool. Then, apply a commercial rust remover or a homemade solution such as lemon juice to the hinge. Allow the rust-removing solution to be on the hinges for a few minutes to penetrate and dissolve the remaining rust.

If you do not want to spend the cost and time to replace your hinges, simply retightening the screws will restore the hinges' functionality. If you've sanded the screws however, it might be necessary to attach an wooden dowel or shim to the hinge. Dowels made of wood are square pieces made of wood in the shape of rods which are available in different lengths and diameters. You can purchase them online, at woodworking supply stores and at home improvement stores.

You can also make an shim out of metal or plastic depending on the type of hinge you own. To make a dowel cut a piece made of wooden dowel or any other durable material to the desired size. You can dip the dowel in carpenter's glue and then insert it into the hole. The glue will secure the dowel in place.

Before you begin cleaning the hinges, place down a cloth or paper towel to protect flooring and other surfaces from accidental spills and drips. After the area has been secured then clean the hinges with an absorbent sponge or a soft cloth dipped in a mild cleaner or vinegar to get rid of the build-up of dirt, grime and tarnish. You can make use of a small or toothbrush brush to reach difficult-to-reach places in crevices and tight areas.