• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Ignition Cylinder Lock Repair

The ignition cylinder lock is responsible for allowing the key to turn and start the car. It is controlled by a chamber containing springs that can be damaged due to environmental factors such as low or high temperatures.

If your ignition switch or key isn't able to move, it could indicate that the cylinder for your lock is damaged and requires to be replaced. This is a job best left to an auto locksmith professional.

Remove the covers for the steering column.

Ignition lock-cylinders are mechanical parts that allow a key inserted into the ignition switch to be turned to turn off a vehicle. They can fail or wear out in a variety of ways, such as keys that are inserted too hard or not in the correct place. They may also fail due to corrosion or other reasons. If your ignition cylinder isn't working, it's probably time to replace it. You can do this yourself, but it's a job that requires you to remove the steering column covers and the airbag cover. The process can be dangerous and complicated, and the replacement cylinder might require special tools to install.

The ignition cylinder is located in the middle of the column, where the steering wheel is attached. It has two screws on the bottom and a clip on the side to secure it in place. It's important to remove these before you begin working on the cylinder, so that it doesn't fall off and get lost ignition key.

Once you have the screws removed, you can pull the plastic retainers out of the lower part of the cover. There's also a metal retainer that clips to the top of the cover to keep it in position. You may have to pull the cover off the steering wheel in order to remove the tabs on the lower part of the plastic.

You can cut them off by removing the screw that holds them and bending the tab slightly outward. If the tab is broken completely it can be replaced with a perforated piece of strapping made of metal that is available at many hardware stores. You'll also need some U-clips to secure the new bottom "tab," and these can be bought from any auto parts store.

Once the plastic tabs have been removed and the airbag cover pulled back, you will be able to access the ignition cylinder hole. Using the 1/16-inch allen wrench you can unlock the ignition lock and push it onto the cylinder retaining pin. Then, you can remove the cylinder. It is possible to replace it with an anti-theft cylinder.

Remove the Ignition Cylinder

While many modern vehicles have transitioned to push-to-start systems, there are still many cars in the market that require an ignition lock cylinder. This mechanical cylinder is located inside the electrically powered device called the ignition switch. It locks the ignition and "reads" anti-theft codes inside the car key to allow it to start.

If your car is showing signs of a malfunctioning ignition lock cylinder, it might be time to call an auto locksmith for assistance. A damaged cylinder could cause numerous issues, including absence of power from the engine as well as problems with inserting and taking out the key. Keys that are damaged by wear can affect the wafer tumblers that allow the ignition cylinder to turn into a jam which prevents your car from getting started.

Depending on the make and model the cover for your ignition switch can be secured with either a clip or screw. By using a screwdriver, loosen up the screw, then remove the cover to reveal the ignition lock cylinder. It's usually a metal cylinder approximately the size of one quarter.

To remove the cylinder, you will need to drill the pin that holds it. Make use of a drill bit that is slightly larger than the slot that holds the key and drill straight into it until the cylinder is broken. You'll then be able pull the cylinder out and replace it with a replacement.

You'll need to refer to your service manual to find out the exact steps to remove the ignition cylinder. After you have the cylinder removed, you can put in your new ignition switch.

You'll first need to replace the covers on the steering column. Also, you'll need to tighten two screws on the top of the lock assembly that secure it. Once you've completed this installing your new ignition cylinder shouldn't be that difficult.

Take out the Ignition Switch

The ignition switch and cylinder lock are two different parts of your car's electrical system. Although they might appear similar, you can repair or replace them in a separate. The switch is the electrical portion that provides power to the vehicle, while the cylinder is the mechanical tumbler that your key is able to slide into. Generally, you can tell the ignition cylinder is not working properly due to its inability to turn your key.

When the cylinder fails and the pins inside the tumbler could wear out, making it difficult or impossible to insert or pull out your key. If you notice that your key is deteriorating and won't turn it is recommended to have the wafers in it replaced or smoothed by a professional locksmith.

Based on the model of your car There could be a screw or bolt that is used to secure the switch and removing it will expose the ignition cylinder. Make sure to consult the manual for your car before you attempt this at home. It could be hazardous and cause damage to the steering column or the plastic covers. Furthermore, the switch is bundled with the airbags' wiring and any interference with this can result in serious injury.

To take the ignition cylinder out you'll need an instrument to loosen it. You can also use pliers to disengage it from the assembly however this is usually more difficult than using the screwdriver. Once the ignition cylinder is removed, you can buy an alternative one at your local auto shop.

After installing the new ignition cylinder you'll have to connect all of the wires to the electrical connections in the steering column and then test it for proper function. It's usually easiest to disconnect the battery first, then take the key from the ignition and then start the engine. You can reconnect the battery after the ignition has worked. If the car ignition lock still doesn't start, you'll need to have the immobilizer reset. This can be accomplished by a dealer or an automotive service technician. This is a lengthy procedure that should be left to an expert.

Reinstall the Ignition Cylinder

The ignition switch in your car sends a signal to the vehicle's engine that it's time to start up. The key inserts into a lock cylinder to start the process, but the pins and wafers within the cylinder may wear out over time. This can make it difficult to turn your car on or even impossible if the cylinder gets stuck.

If your key doesn't turn on the ignition, it is likely that it needs to be replaced. Locksmiths can replace your ignition cylinder with a similar one so that your key can still work with your existing ignition switch.

To take out the lock cylinder that was previously in use to remove it, push it into the release pin located at the bottom of the assembly and lift the cylinder out of its housing. If the cylinder doesn't slide out, try pushing on the release pin again or using a screwdriver to press an anti-rotation small button underneath the cylinder's face. You can also push in on the cylinder while adjusting the key to the ACC position or use an accessory to force it out.

Install the new cylinder and test it by turning on the vehicle. If it's not it's working, you can connect the trim pieces were removed to gain access to the cylinder and follow an anti-theft procedure to connect your new keys to the vehicle.

Although the cylinder lock in the ignition isn't as crucial to the functioning of your car ignition switch as it was in the past but there are still situations where you may require replacement. Talk to a professional such as an automotive dealer or locksmith to ensure that the job is done without damaging the steering column or other parts of your vehicle. It's also crucial to ensure that the new ignition cylinder is correctly coded to ensure that your vehicle recognizes it as a genuine key. This will usually require a professional or a dealer to carry out this relearning.