• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500 stolen without keys 500 Key Fob Won't Work

A key fob for fiat ducato key fob programming 500 allows you to easily open doors and start your car. However, there are a variety of reasons why the fob won't be working. This could be due to a dead coin battery, damage to the receiver module, water issues, and interfering.

This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths in the automotive industry). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob that isn't working. Key fobs of today have a limited range of operation and must be within a few inches of your vehicle in order to function. If you are far from your vehicle, and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. You can typically find them at your local hardware store, or online.

You can test the battery of your coin-cell by pressing the buttons while standing near your Fiat 500. The car should flash its parking lights, and the key fob should be able to operate the lock and unlock switches.

If your key fob still does not work after replacing the battery, there may be water damage which hinders it from connecting to the module in your vehicle. Water damage can happen in a variety of ways, such as simply splashing or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this isn't working, you'll have to get your fob reprogrammed either by an auto locksmith or a dealer.

Water Damage

While the fob has some rubber seals that keep water from the chip's electronic circuit it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to become shorted and eventually fail. It's not a good thing to submerge the fob in water, but don't give it up in the event that you accidentally drop it in water or forget to take it out of your pocket.

First, remove the battery from the fob. Clean the electronic chip with isopropyl or a similar product and dry it thoroughly before replacing the battery. Check the fob again to check if it's working. If the key does not function, it may need to be programmed again. This is usually handled by a professional or dealer auto locksmith.

If the key is a newer model and has not been programmed to your vehicle it is likely to need to be replaced completely. This is a straightforward process that can be completed by a professional automotive locksmith. The locksmith will require the key cut to match your car's ignition. They will also need to reprogram the fob to your vehicle's system. It's a simple and affordable process that can usually be completed on the same day.

Receiver Module Issues

The 500 key fob could be inoperable because it's out of range. The remote has a maximum range of 30 feet, so in the event that you are far away from your vehicle, it won't respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If your fob doesn't work after replacing the battery in the coin, also known as a "button", "watch" or "button", it may be due to a malfunction on the circuit board inside. Reprogramming the fob usually resolves this issue. You can find the instructions for the majority of vehicles on YouTube or in the owner's guide.

It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension, it could prevent the coin battery from being properly seated and can cause the remote to malfunction.

In rare cases the fob could be out of the vehicle's sync because of software or hardware problems. This could cause a significant headache, but you can often fix this by visiting a local dealer or auto locksmith to reprogram your fob. In certain situations, they may need to install the software again in your body control module, as well.

Interference

Interference can also cause the key fob to not be able to receive or transmit a signal. This could happen when the keyfob's location is in close proximity to a radio transmitter, like a cell phone or radar detector. Other reasons the key fob could not function include a poor connection to the buttons or the internal chip, or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. You might have a damaged 500 receiver module if you've tried replacing the battery, Repairer reprogramming it, or using a spare key cover fiat 500 fob. The receiver module, located beneath the dashboard, detects radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the onboard systems in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then reconnect the battery. This will clear out any remaining electrical charge and restart the car's computers. This could help get your key fob working again. If the issue continues you should speak with an experienced technician. They will be able to determine the root of your problem.