• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Repairing a broken door hinge can be a doable job for most homeowners. But, if the holes for screws are smashed and aren't able to hold screws, you might have to use dowels and wood glue before you can reinstall the hinge.

Remove any surface rust. This will help to keep the dowels in place and give them an adequate base for them to rest on.

Eliminating the Hinges

Many hinges for doors can be removed, making it easier to move the door from one end of the frame to the other or take the entire door off when needed. Anyone with a little patience can remove the hinges however, you must know what to do.

If the hinges have been painted, you'll need to remove it before you attempt to remove the pins. If you don't, the paint could peel off and scratch your door when you attempt to lift it. Place the hinges in an stainless steel pot and fill it with water to the point that the hinges are completely submerged. The hinges should remain in the pan for approximately 30 minutes. The heat from the water should soften the paint and make it easier to get rid of the pins.

After the pins have been removed, take the hinges and the frame from the door. It is possible to use a regular screwdriver, but it is recommended to use a magnetic screwdriver for this job. This type of screwdriver was created to grab screws made of metal and can make the work speed up.

It is a good practice to spray some lubricant on the hinges prior to attempting to remove them. A simple lubricant can make the process move along quickly and aid in the removal of the pins and screws. You can find this kind of lubricant at a variety of hardware and home improvement stores.

Keep in mind that the number of door hinges you'll require will differ based on the kind of door and its configurations. Solid-cored and heavier doors will require more hinges, whereas hollow-cored and lighter doors might only require two or three hinges.

Understanding the different kinds of hinges will help you decide which one is the best for your particular situation. The hinges on the exterior are designed to support the weight of a door, but interior hinges must be able to support heavier loads.

Reattaching the casement windows hinges

Sometimes a door hinge will become looser over time and begin to hang out of alignment or slide. It can be a big issue, but the solution is usually simple. Most of the time it's a simple tightening of the screw will solve the issue. If the screw holes have been ripped out, it can be difficult to do. However, there is a trick to get these holes tight again using a wooden dowel.

Start by drilling the old hole using a drill bit close to the size of the new screw (normally 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a snug fit, the dowel should be cut to the same length as the screw. Then, you can reinstall the screw and tighten it to the desired tightness. If the door still has the tendency to be bowed and close, then you can add another dowel to the gap and repeat the process. Be sure to shut the door slowly in order to examine the clearances around the perimeter after each adjustment.

You can also use a wooden plug instead of the dowel. This is also a viable option however it will take a bit longer to install. You can tap in the wood piece that has been whittled to the right size. If you don't own an instrument for woodworking, you can use toothpicks or matchsticks made of wood.

After you've reinstalled your new screw then use a countersink to make the hole for the head of the screw smaller so that it does not rub against the edge of the door when it's opened and closed. This will aid in tightening the screw prior to reinstalling the hinge.

After you have reinstalled the glass hinge, be sure to grease it with a dry lubricant to prevent it from getting stuck in the future. Products like PB Blaster or Liquid Wrench are great alternatives. Apply a thin coating and allow it to soak into the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you are not ready to replace the hinges on your door, you could make a few minor repairs. The first step is to make sure that the screws securing the window hinge repair plate to the door frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be careful not to tighten your screws to the point that they start to cause gaps at the trim joints or, even more damagingly cause threads to be stripped.

If you're experiencing issues because the hinge plates are separated from the door and jamb and jamb, you can fix them by gluing wood glue to the back of the plates and then inserting wooden dowels or toothpicks into the holes. Dowels or toothpicks will provide a solid base for the screws and help to prevent the plates from shifting when you drive them into the holes. Let the glue dry before attaching the hinge.

The screws may also be stripped or missing. You can fix this problem by replacing the screws with longer ones. Use a drill bit that is the same size as the screw hole to prevent drilling into the hinge or jamb.

After you've reattached your hinge, close the door and look at the gap between the frame and the door. The gap should be the thickness of a penny or less if an old door was hung incorrectly. If the hinges were put in place correctly, this shouldn't be an issue.

If the hinges are still loose, you can add an extra thick hinge between the surface of the hinge plate and the mounting surface. This will allow the hinges more room. You can also try removing the hinge pin from the problematic hinge and pounding it down using a hammer to make it tighter or use the hinge pin from a different angle altogether. You can also grease your hinges with mineral oil or jojoba to reduce friction and help keep them in position. Lubricating your hinges periodically can stop them from becoming stiff and squeaky, and also prolong their lifespan.

Cleaning the Hinges

The friction caused by the hinge's constant motion draws dust particles. If there is no regular cleaning or lubrication, these particles become stuck in the moving parts of a door hinge tilt and turn window hinge covers accumulate over time. In the end, the hinge becomes stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication, and inspection can preserve the integrity of a hinged door and ensure their proper operation.

Inspect the hinges to see how much rust has built up on their surfaces. If the rust has corroded to the point of destroying the surface of the hinge barrel or screw holes, you'll need to replace the hinges. If you are able to save the hinges, remove any loose rust using steel wool and wire brush. Apply a commercial rust-removing product or homemade solution like lemon juice on the hinge. Let the rust remover remain on the hinge for a few minutes to penetrate and dissolve any remaining rust.

If you don't want to spend the money and time replacing your upvc window hinges replacement, simply retightening the screws will restore the hinges' functionality. It might be necessary to attach an shim of wood or a dowel to the hinge if the screw holes have been stripped. Dowels made of wood are available in round rods of various sizes and lengths. You can find them at home improvement stores as well as woodworking supply and craft shops, or on the internet.

You can also make an shim using made of plastic or metal depending on the kind of double glazed window Hinge repair you own. To make a dowel, cut a piece of wooden dowel or other sturdy material to the size you want. You can then dip the dowel in a glue for carpenters and then insert it into the cut hole and let the glue hold the dowel in place.

Before cleaning the hinges, put down a piece of paper cloth or towel to shield your flooring from spills. After securing the area clean the hinges with an easy sponge or cloth coated with a mild cleaner to remove dirt, grime, and tarnish. You can make use of a toothbrush or a small brush to get into difficult-to-reach areas in crevices and tight areas.