• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of steps that are unique to add an additional ignition key. It requires dealer assistance using the handheld computer known as Tech-2. Then a new key as well as transponder have to be purchased and then programmed into the car.

It is a good idea to rotate your keys in order that one does not wear out more quickly than the other. This will help keep your keys in good condition.

Replacement Case

The new key fobs for keys are not like the older Saab keys. They are equipped with electronics that make it difficult to copy. This has made stealing cars much more difficult than twenty years ago. It has also made it more expensive to replace lost keys.

saab car key replacement key Programming (telegra.ph) 9-3 owners should have two keys working. If one is lost saab key, it costs a lot to get another one for the car since it requires replacing the CIM module and re-programming the locking cylinders. Dealers typically charge between $100 and $200 to do this.

There are ways to reduce the high cost. Some parts suppliers will look up the code from an extra key (usually the same one that opens the doors and switches the ignition) and cut a new metal key blade at less than the dealer's cost. The key, however, must be the same as the original one to function properly within your car.

You can also change the case yourself by following these steps. You'll require an open-faced screwdriver and patience. With the screwdriver, slowly tear the plastic away and separate the emergency keys from the case. Once you have the case open, remove the electronic components and put them in your new case. Make sure to insert the correct key and badge back in the case too.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost part that can be replaced easily and quickly. This YouTube tutorial for DIY Cyclone Cyd will show you how to replace the battery of the remote key fob in only four steps. This guide should work with any modern saab key fob, though the process may vary slightly.

The first step is to locate the button that releases the backup key on the fob. This button is typically located on the back of the fob right next to the Saab Logo. Use a flathead to insert the screwdriver into the small hole in this button. This will be enough to allow you to open the fob's case so that you can replace the battery.

After the new battery CR1632 is in place it is possible to reassemble the remote key fob and program it to your car. The entire process should not take more than one hour. It's a very easy procedure that doesn't require any special tools.

If you lose a key the process will be a bit more involved however, it can be done. The dealer must read the car's VIN and then order a replacement key blade and TWICE module that has the proper unique code. The dealer will then need to program the key using MDI an innovative software tool.

Replacement Key Fob

The key fob is the device that locks and unlocks your car, it's got a battery within. Batteries are able to last for a short time and eventually die. This is a problem that occurs for all vehicles. The good news is that you can replace the battery in most key fobs, and not have to replace the entire case. You can purchase replacement fobs from Amazon that have all the electronics already installed, so you'll be able to just pop open the case and replace the batteries that were in the case. It is necessary to remove the emergency key before you can replace the batteries. To accomplish this, simply insert the screwdriver of a small flat head into the slot that is in the middle. Use the screwdriver to move around the case until it will split open, making it much easier to remove.

If you're ready to replace your keys, have an extra set on hand. This will save you a lot of money. If you have spare keys, you can request that the dealer cut a new key and program it into your car, which is much cheaper than replacing the whole key fob.

If you do not have a spare key, it is possible to add a second key to your car, however it requires a lot of research and effort. A second key can cost a few hundred dollars, and it also requires the programming of the car's computer. Professionals can do this but it's not a cheap option.

Replacement Ignition

In contrast to earlier saab keys replacement automobiles, the new SAAB 9-3 models are equipped with a much more sophisticated alarm system that is built around a coded key. This means that when you lose your sole working key, replacing it with another one can be very expensive since the car has to have a unique computer module installed, and it also must be specially programmed to accept an extra key. Most locksmiths can't do this or even dealers will charge hundreds of dollars just to program the new key!

If you've lost your only working key the dealer will replace your car's computer (known as the CIM or SAAB TWICE) to make the replacement, and will charge you the highest price for it. We can reprogram the existing EEPROM inside your car's computer so that it is ready for an extra key. This will save you more than 50% of the cost you would spend at the dealer.

If you've been a long time owner of an 03-11 SAAB 9-3, you probably have noticed that the ignition switch isn't very robust. If the ignition key you have isn't working properly, you should think about replacing it. They can become sticky and the buttons have been known to fall off. It's not as difficult as it seems to replace the ignition key. With the appropriate tools, it could be accomplished in a short time.