• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

This will make the panel sit flush with the PT-10 case top. The cables should be connected so the cable sits flat against the top side of the CS PCB and the bottom side of the base PCB, so the solder joints are on the inside of the bent cable. Also, don't solder the wires INTO the holes, strip, tin and solder tinned ends flat against the pads. The best way to strip the insulation from the wires is to lightly score with a knife on the flat side, i.e. cut half-way through the insulation, not cutting to the wire, then do small cuts between each wire (from the score line to the end), then pull off each little bit of insulation with pliers, being careful not to grip the wire too much and pull the wire out. This is a slightly difficult process, so I'll give as much advice as possible.

Added some info to the Spectra page on a possible way to recover form the FAIL 01/90 error, as well as some more manual part numbers. Added some info to the JT1000 page about which radios support QCII, as well as a link to the .pdf of the Operator's Manual. Added a warning to the Maxtrac page about repeater/linking modifications and 900MHz radios. See the info page more details. If you are interested in the electronical details of PC parallel ports and the X1541-series cables, please, read the Technical background information section in The Star Commander documentation. On 286, 386 and older 486 machines, the parallel port is on a separate card (e.g. I/O card, parallel port card, Hercules video card with a built-in parallel port) and it is SPP or PS/2. On newer 486 and all Pentium (and above) machines, the parallel port is integrated onto the motherboard and you can set its mode in the BIOS setup. Now you can take a 220 Ohm resistor and insert it into one set of pads of R40-R55 and see how bright the LEDs are. If it isn't then you might find jumpers on the card to set the mode.

For we should not go to war with Portugal, and if we went to war with any other Power, Portugal, being a neutral Power, might preserve the cables landed on her shore intact against a belligerent. It would appear that there was a major system crash, and that is why they went down. Make sure there are NO SHORTS between any two adjacent pins of the ribbon cable joints. Control cables are multi-conductor cables used in automation and instrumentation applications. SPP mode means bidirectional control lines and unidirectional data lines. PS/2 differs from SPP in that its data lines are also bidirectional. What does the data 300V/500V or 600V/1000V mean? Mount the panel to the PT-10 case, using nuts to hold it on, then attach the PCB. Ideally you should not make a raised solder joint on this side, only get solder to be sucked into the hole, to hold the cables in place so you can do proper solder joints on the other side.

The answer is threefold: (a) American cables landing on British shores fall, ipso facto, under British control in case of war, and therefore can only add to our strategic resources. In these circumstances, the existing Halifax-Jamaica line, built under subsidy from Halifax to Bermuda in 1890, and from Bermuda to Jamaica in 1898, appears adequate to the needs of the case. It is to be hoped that such an outlay of public money may be avoidable in this case. A non-American governmental edict may still be copyrighted outside the U.S. If you are using some ultrabright or superbright LEDs, blue or white LEDs, etc. you may want to try 2K, 3K or higher resistors. Possible modes are SPP, PS/2, EPP and ECP. By a fortunate and unusual economy it was found possible to use all the existing stations of the first cable. The X1541 cable makes use of the bidirectional control lines.

If you have any sort of inquiries pertaining to where and how you can make use of what is control cable, you could call us at our own site.