• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat panda remote key replacement 500 Key Fob Won't Work

A key fob for the fiat car key 500 allows you to easily open doors and start your car. There are many reasons why the fob may stop working. These include a dead battery, damage to the receiver module, water issues, or interference.

This listing is for an NEW replacement fiat key code Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Key fobs of today have only a limited range of operation and must be within a few inches of the vehicle in order to function. If you are far from your vehicle and you press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) by a new one from a reliable brand like Panasonic, Duracell, or Energizer. They are usually available in your local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while standing close to your fiat panda key 500. The parking lights should light up and the key fob should operate the lock and unlock switch.

If the fob's key doesn't function after replacing the battery, it might be damaged by water, which prevents it from communicating with the receiver module in your vehicle. Water damage can occur in many ways, including simply splashing or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, you will need to have the fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob in the ocean or wash it in a washing machine. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually die. In the event that you let your fob get wet, it's not a good idea however, if you drop it into the water in a cup or do not remember to remove it from your pocket before you run the washing machine, don't give up hope.

First remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or similar products. Check the fob to check if it's working. If the key doesn't function then it might need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is old and has not been programmed for your car You will need to replace it completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith will need the key cut to match the car's ignition. They'll also have to program the fob into the car's system. It's a simple and inexpensive process that is usually completed in the same day.

Receiver Module Issues

One of the most common reasons your 500 key fob won't be working is that it's simply out of range. The remote's range is of 30 feet. So if you are too far from your vehicle, it won't respond to your commands. It can be solved by moving it closer to your vehicle until it starts responding.

If you've replaced your coin battery (commonly known as a "button" or "watch") and your fob still won't work it could be due to an internal circuit board problem. Reprogramming the fob is usually the solution to this problem. You can find the steps for most vehicles on YouTube or in the owner's guide.

You may need to replace the metal retaining clips that keep the coin battery in place. If they lose tension, it may prevent your battery from sitting properly and cause your remote to malfunction.

In rare instances the fob could be disconnected from your vehicle due to software issues or hardware issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In My Area certain situations it may be necessary to install the software again in your body control module as well.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This can occur when the keyfob's location is in close proximity to a radio transmitter, like a cell phone or radar detector. Other reasons why the key fob could not function include a weak connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while suddenly and you've tried every option at home to fix it e.g. battery replacement, reprogramming and using the spare key fob, you could have a faulty receiver module on your 500. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will remove any remaining electric current, and also restart the computer in your car. This will help you get your fiat punto key fob to function again. If the issue persists you should seek out an experienced technician. They will be able diagnose the exact cause of any issues.