• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door hinge a Loose Door Hinge

Fixing a loose door hinge can be a doable job for most homeowners. If, however, the holes for screws are smashed and can't hold screws, you might need to put in dowels and wood glue before you can install the hinge.

Brush away any surface corrosion. This will aid in keeping the dowels in place and give them a solid base for them to rest on.

Take the Hinges off

A lot of door hinges can be removed, which makes it easier to move the door from one side to the other or to take the entire door off of the frame should it be needed. The removal of the hinges is easy for anyone with patience, though you do have to know how to do it properly.

If the hinges are painted, you will need to remove the paint prior to attempting to remove the pins. If you do not, the paint may peel off and scratch your door when you attempt to lift it. To break the seal put the hinges in a stainless steel dish and fill the pan with water until the window hinges are completely submerged. Allow the hinges to sit in the pan for around 30 minutes. The heat of the water will soften the paint making it easier to remove.

Once the pins have been loose, remove the hinges and frame from the door. It is possible to use a regular screwdriver, but it is recommended to use a magnetic screwdriver for this job. This type of screwdriver has been specially designed to pick up screws made of metal and will help you get the job accomplished much faster.

It is a good practice to spray some lubricant on the hinges prior to trying to remove them. A simple lubricant can make the process to go more quickly and aid in the removal of the screws and pins. You can find this type of lubricant in most hardware and home improvement stores.

It is important to keep in mind that the number of hinges you'll require will vary depending on the type of door and its configurations. Doors with solid cores and heavy weights will require more hinges whereas hollow-cored doors that are lighter may only require two or three hinges.

Understanding the various types of hinges will help you determine which one is best for your particular situation. The hinges on the exterior are designed to support the weight of the door and interior hinges need to be able to handle lighter loads.

Reattaching the Hinges

Sometimes, a hinge on a door will become looser over time and begin to hang crookedly or slide. This can cause problems but is usually easy to fix. Retightening the screw will typically solve the problem. If the screw holes have been ripped out, it can be difficult to do. A wood dowel can be used to tighten these holes once more.

Begin by drilling out the old hole using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length that is the same as the screw to ensure a secure fit. Install the screw again and tighten it until you are satisfied with the level of tightness. If the door is still unable to be bounded up, you can insert another dowel into the gap. Repeat the procedure. Be sure to close the door slowly to examine the clearances around the perimeter after each adjustment.

Another option is to just make use of the wood plug instead of dowel. It works equally well, but may take a little longer to set up. You can insert a piece of wood that has been whittled to the right size. If you don't own a woodworking instrument or toothpicks, you can make use of toothpicks or matchsticks made from wood.

After you've reinstalled your new screw then use a countersink to make the hole for the head of the screw smaller, so that it doesn't rub against the edge of the door when it is opened and closed. This will make it easier to tighten the screws before reinstalling hinges.

Once you've reinstalled your hinge, be sure to coat it with a dry lubricant to ensure that it doesn't get stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. You should apply a light coat and allow it to take about 15 minutes to fully get into the barrel of the hinge.

Refinishing the Hinges

If you're unsure whether to replace hinges, you could try a few fixes. The first step is to make sure whether the screws that secure the hinge plate to the door and frame are tight. If they're loose, tighten them with the help of a screwdriver or a power drill. Be careful not too tighten the screws, because this could cause gaps to form at the trim joints or worse, strip the threads.

If the problem is the hinge plates are splitting they can be reattached to the plates by applying wood glue to the side of them and inserting wooden dowels or toothpicks into the holes. The toothpicks or dowels will serve as a solid base for the screws and keep the plates from moving when you drive them into place. Let the glue dry before reattaching the hinge.

The screws can also be damaged or missing. You can fix this problem by replacing the screws with longer ones. Use a drill bit that is the same size as the screw hole to avoid drilling into the jamb or hinge.

Close the door once you've reattached the window hinge repair and check the gap between the frame and the door. The gap should be about the thickness of a penny all around or less if an older door was hung incorrectly. This shouldn't be a problem if the hinges are installed correctly.

If you discover that the hinges are still loose, try adding an extra thicker shim between the hinge plate and the mounting surface, to create a little extra space. You can also remove the hinge pin and then pound it down with a powerful hammer in order to tighten it or use the hinge of a different type. You can also grease your hinges with mineral oil or jojoba in order to reduce friction hinges uk and hold them in their place. Lubricating your hinges periodically can keep them from becoming stiff and squeaky, and also extend their lifespan.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. Without regular cleaning and lubrication, these particles become stuck in the moving parts of a hinge for doors and build up over time. The hinge will get stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication, and inspection will preserve the quality and function of hinges that are attached to doors.

Examine the hinges for corrosion. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you can save the hinges, clean any loose rust by using wire brush and steel wool. Then, apply an industrial rust remover or a homemade solution, such as lemon juice to the hinge. Let the solution that removes rust remain on the hinges for a few minutes to penetrate and dissolve any remaining rust.

Retightening screws can help restore hinge function If you don't wish to spend time or money to replace window hinges hinges. If you have stripped the screw holes however, it could be necessary to attach the dowel of wood or shim to the hinge. Wooden dowels come in round rods of varying sizes and lengths. You can buy them on the internet, at woodworking supply shops and home improvement stores.

A shim could also be made from a piece of plastic or metal, based on the kind of hinge you have. To make a dowel cut a piece of wood dowel or other sturdy material to the size you want. You can then dip the dowel in a glue for carpenters and then insert it into the cut hole and let the glue hold the dowel in place.

Before you start cleaning the hinges, put down a cloth or paper towel to protect flooring and other surfaces from accidental spills and drips. Once the area is protected then clean the hinges using an absorbent sponge or a soft cloth dipped in a mild cleaner or vinegar to get rid of built-up dirt, grime and tarnish. You can make use of a small or toothbrush brush to reach difficult-to-reach places in crevices and tight areas.