• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Loose door hinge a Loose Door Hinge

Most homeowners can repair hinges that are loose. However, if the holes for screws are smashed and can't hold screws, you might have to use dowels and wood glue before you can install the hinge.

Brush away any surface corrosion. This will help to keep the dowels in their place and provide a solid foundation for them to rest on.

Take off the Hinges

A variety of door hinges can be removed, making it easier to move the door from one end of the frame to the other side or take the entire door off when needed. Removing the hinges is fairly simple for anyone with a bit of patience, though you do need to know how do it right.

If the hinges have been painted you'll need to take off it before you attempt to remove the pins. If you do not, the paint may peel off and scratch the door when you attempt to lift it. To break the seal put the hinges into a stainless steel dish and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for approximately 30 minutes. The heat of the water will soften the paint, making it easier to take off.

Once the pins are loosened and the pins are loose, you can take off the hinges for upvc doors from the door and frame. It is possible to use a regular screwdriver, however it is recommended to use a magnetic screwdriver for this project. This type of screwdriver is specifically designed to take out metal screws and will assist you in getting the task completed much quicker.

Before you attempt to remove the hinges, it is a good idea to spray them with some grease. A simple lubricant can help you to accelerate the process and remove the pins and screws more easily. You can find this type of lubricant in most hardware and home improvement stores.

Keep in mind that the number of door hinges you'll need will vary based on the type of door and its configurations. Heavier and solid-cored doors will require more hinges whereas lighter and hollow-cored doors may only need two or three.

Understanding the various types of hinges will help you determine which one is suitable for your needs. Exterior hinges are generally designed to support the door's weight, while interior hinges will need to be able to handle lighter loads.

Reattaching the Hinges

Over time the hinges on doors can loosen and begin to sag or hang crookedly. This can cause problems but is usually easy to solve. Most of the time an easy tightening of the screw will resolve the issue. If the screw holes have been ripped out, it can be difficult to do. There is a method to make these holes tight again that uses a wood dowel.

Start by drilling the hole using a drill bit close to the size of the new screw (normally 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a secure fit, the dowel must be cut at the same length as the screw. Reinstall the screw and tighten it to the desired level of tightness. If the door continues to bind up, insert a second dowel into the gap. Repeat the procedure. Close the door slowly after each adjustment to ensure that the perimeter clearances are in order.

You can also use a wooden plug in place of the dowel. It works equally well, but may take a bit longer to put in. You can tap in a piece of wood that has been whittled to the proper size. If you don't have a woodworking instrument, you can use toothpicks or matchsticks made from wood.

Use a countersink to make the hole smaller for the head of screw after you have reinstalled it. This will prevent the screw from rubbing against the edges of the doors when they are closed and opened. This will make it much easier to tighten the screws before replacing hinges.

Once you've reinstalled your hinge, make sure to grease it with a dry lubricant to prevent it from getting stuck in the future. Products such as PB Blaster or Liquid Wrench are excellent alternatives. Apply a thin layer and allow it to penetrate the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you're unsure whether to replace your hinges, you can try a few fixes. The first step is to check that the screws securing the hinge plate to the frame and door are tight. If they're loose, tighten them with a screwdriver or power drill. Be cautious not to over tighten the screws, as this can cause gaps to appear at the trim joints or worse, strip out the threads.

If the problem is the hinge plates are separating they can be reattached to the plates by putting wood glue on the back of them and then inserting wooden dowels or toothpicks into the holes. The toothpicks or dowels will give a solid foundation for the screws and to prevent the plates from shifting when you drive them into place. Allow the glue to dry before reattaching the hinge.

The screws may also be damaged or missing. This problem can be fixed by replacing the screws. Be sure to use a drill bit that is compatible with the size of the screw hole to avoid drilling into other parts of the hinge or jamb.

After you've reattached your hinge, close the door and look at the gap between the frame and the door. It should be about the thickness of a nickel all around or less if there's a gap caused by a door that hung improperly. This shouldn't be a problem as long as the hinges are installed correctly.

If the hinges still seem loose, try adding a stronger hinge between the upvc window hinge plate's surface and the mounting surface. This will allow the hinges more space. You can also remove the hinge pin and then pound it down with a heavy hammer to tighten it, or install the hinge of a different type. You can also lubricate your hinges using mineral oil or jojoba to reduce friction and keep them in position. Regularly lubricating your hinges will aid in keeping them from becoming stiff or squeaky and will also prolong their lifespan.

Cleaning the Hinges

A hinge's continuous movement causes friction, which attracts dust particles. Without regular cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and then build up over time. In the end, the hinge becomes stiff and creaky, and its appearance can deteriorate rapidly. Regular cleaning, lubrication, and inspections will maintain the integrity and functionality of hinges on a door.

Inspect the hinges to see how much rust has accumulated on their surface. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace the hinges. If you can save the hinges, begin by brushing off any loose rust with steel wool and wire brushes. Then apply an industrial rust remover or homemade solution like lemon juice to the hinge. Allow the rust-removing solution to sit on the hinges for several minutes to penetrate and dissolve any remaining rust.

If you don't wish to spend the money and time replacing your hinges, simply retightening the screws can bring back the hinge's functionality. It may be necessary to add an shim of wood or a dowel to the hinge when the screws have been stripped. Dowels made of wood come in round rods of various lengths and sizes. They are available at home improvement stores as well as woodworking supply and craft shops, or on the internet.

You can also make a shim from a piece either plastic or metal, depending on the kind of upvc window hinge problems you own. To make a dowel cut a piece of wooden dowel or another sturdy material to the size you want. You can dip the dowel into the adhesive of a carpenter and insert it in the hole. The glue will secure the dowel in the desired position.

Before you begin cleaning the hinges, lay down a towel or a paper towel to shield flooring and other surfaces from spills and drips that may happen. After securing the area then clean the hinges using a soft sponge or cloth coated with mild cleaner to get rid of dirt and grime. You can also remove tarnish, dirt, and grime. You can use a toothbrush or small brush to get into difficult-to-reach areas in crevices and tight areas.