• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

It is easy to replace a broken window handle using the appropriate tools. It is important to know the type of handle you have and its spindle size before you purchase a replacement.

Older uPVC window handles have a spur that protrudes and locks over the wedge striker for cockspur. These can be either left or right-handed and need to be replaced with the same handle.

What type of lock and handle do I have?

There are a myriad of upvc window locks and handles each with its particular advantages and uses. The type of handle that you own will determine if the locking mechanism you have is effective and also if it is simple to open the windows. As time passes, and with regular use, the upvc handles on your windows may become damaged and worn out. This makes them less secure and less effective. In some cases, they may even fall off completely. If you notice that your upvc window handles have been removed, it's essential to repair them as quickly as possible. This will stop possible burglaries, and keep your house secure.

The good news is that replacing your upvc window handles is a relatively simple task that is achievable by nearly everyone. You'll require a few tools, but with the appropriate knowledge, it's an easy task that will only take a couple of minutes. You must know the type of lock or handle you have on your window. This will allow you to choose the right windowpane replacement.

Inline Espagnolette Handles

They are the most popular type of upvc handle and are typically located on the side of your window. They are flat and have a latch which engages the locking mechanism of the window frame. Inline upvc handles come with a spindle running through the middle of the handle and into the window frame in order to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are secured to the frame of the window with one screw, and are less secure than other kinds of window handles.

Handles that tilt and turn

As opposed to the other handles made of upvc the tilt and turn handles can be turned to open the window, and the handle can be tilted to the side to allow ventilation. They typically have a 7mm spindle on the side of the handle. They are available in both left and right-handed versions.

When you are purchasing replacement handles for upvc it is essential to measure the spindle's length as not all are identical in size. Drop something in the middle of the hole to measure the length. This is the maximum spindle size that will fit your windows.

What is the spindle?

uPVC window handles function in a similar way as doors. By turning the handle, you will be able to open a latch in the frame. This unlocks the window so that it can be opened and closed. The handles could be damaged, especially if frequently used or exposed to harsh conditions. It is possible to replace the handles on your uPVC window if they're not operating correctly.

There are many different types of uPVC handles, including Espag, Cockspur, and Spaded handles. They are designed to fit into the uPVC frames in a variety of ways and each handle type uses a specific spindle to lock the mechanism into the window. It is essential to determine the type of handle you have installed on your uPVC windows to ensure that you replace it with the right one.

You can find out what kind of uPVC handle you are using by looking at the base section of the handle. A snap-in cover is over the screw that holds the handle's base in place. Once you remove this, you will be able see the second screw that holds the handle base in position. After both screws are removed you should be capable of pulling the handle away from the uPVC window.

After removing the uPVC handle, carefully unscrew it from the locking mechanism. Make note of the length of the spindle, as you'll need to make sure that you buy a replacement that has the same length as the original handle and locking mechanism.

The spindle wears down and cannot operate the locking mechanism. This could be due wear and tear from continuous use or a loosening of the locking mechanism or even corrosion over time. When this happens it is required to replace the window handle and the locking mechanism to restore the full functionality to your uPVC windows.

How do I get rid of the old handle?

Window handles are susceptible to being damaged or broken over time. It is crucial to repair them as quickly a possible to ensure your security. The good news is that replacing a damaged or worn handle is a easy task that can be completed in just over a minute and doesn't require any specialist tools.

To remove the handle, first remove the screw located at the base of the handle. Once this is removed the handle can then be removed from the base. There is a second screw that is located at the bottom of the handle base, and it is able to be removed as well. Once these two screws have been removed, the handle will be detached from the window's base.

After removing the old handle, align the fixing holes of the new handle with the existing holes in the window frame. If there is a sticker or cap on the new handle, take it off it if necessary and then put the handle back in the appropriate position. It is crucial to verify that the handle works once it is put in place. Turn the handle over and make sure that the lock mechanism is in place.

Espag handles come with spindles that protrude out of the handle and slot into the multipoint locking mechanism that is on the frame of the window. Cadenza windows have a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and are hung over the frame that surrounds the window or the transom crossmember of the bar.

After you have put in the new handle, place the spindle into the window lock and tighten it. Replace the snap-in cover and screw cap (if applicable) once the handle has been firmly fixed. The handle is now ready for use, so try opening and closing the window a few times to check that it works properly and securely.

How do I put in the new handle?

Switching your uPVC window handle isn't difficult, and the process is simple. All you need is a screwdriver and a little bit of patience. First, make sure the handle is not locked. Remove any screws that are visible. You could also replace them with screw caps. After removing the handle you will need to note the length of the spindle which extends from the back. This is crucial as it will determine the type of handle you'll need to buy.

Espagnolette handles made of uPVC are the most popular kind of handle. The spindle runs through the handle to activate the locking mechanism in the frame of the window. When the handle is turned, it opens the latch on the window, allowing it to open. Over time and through regular use, espagnolette handles may be damaged or damaged, making it necessary to locate an alternative.

Cadenza handles are a kind of uPVC handle that is typically used with tilt and turn windows. They feature an elongated blade that functions as an interlocking mechanism that is multipoint within the window. They are generally more secure than espagnolette handles since they are only accessible from the inside. You can replace them with the same procedure as you would with espagnolette handles however, make sure that the new handle is not angled and flat.

Once you have decided on the correct handle to purchase You can simply line up the new handle with the existing screw holes and then screw it in place. Then, put the screw covers on and test the new handle. You can do this by dragging the handle between the locked position to the unlocked a few time. If you encounter any issues, it may be worth contacting a specialist to determine if they can help resolve the problem. They can advise you on how to fix the issue in a quick and effective manner.